Contents and categories

Display all

Contents and categories

Series

Search suggestions

Display all results

IPA 424 T

4-channel DSP Installation Amplifier 4 x 240 W @ 4 Ohm / 70V/100V
Item No.: LDIPA424T
Series: IPA
Versions:
Professional 4-channel installation amplifier
Powerful class D power amplifier with 4 x 240 W (IPA 424 T) or 4 x 120 W (IPA 412 T) at 4 Ohm (transformer bypass) or 70V/100V outputs through toroidal core transformer
Stereo/parallel/bridge mode selector switch per channel pair
4 balanced line inputs and 4 speaker outputs with terminal block connections
User-friendly front panel with signal, limit, protection, mute and bridge mode LEDs per channel and clipping LEDs for the inputs
Speaker protection circuits: DSP limiter, overcurrent, direct current, overheating, short circuit as well as switchable auto standby mode
DSP presets with HPF and LPF which can be activated via DIP switches
REMOTE audio and control bus based on CAN architecture (Controller Area Network)
Equipped for future LD Systems remote control panels and paging microphones
Slot for future optional expansion cards for Ethernet or Ethernet + Dante
Optional accessories: 19" L-bearing rails, length 450 mm
 

Contents and categories

Display all

Contents and categories

Series

Search suggestions

Display all results
Professional 4-channel installation amplifier
Powerful class D power amplifier with 4 x 240 W (IPA 424 T) or 4 x 120 W (IPA 412 T) at 4 Ohm (transformer bypass) or 70V/100V outputs through toroidal core transformer
Stereo/parallel/bridge mode selector switch per channel pair
4 balanced line inputs and 4 speaker outputs with terminal block connections
User-friendly front panel with signal, limit, protection, mute and bridge mode LEDs per channel and clipping LEDs for the inputs
Speaker protection circuits: DSP limiter, overcurrent, direct current, overheating, short circuit as well as switchable auto standby mode
DSP presets with HPF and LPF which can be activated via DIP switches
REMOTE audio and control bus based on CAN architecture (Controller Area Network)
Equipped for future LD Systems remote control panels and paging microphones
Slot for future optional expansion cards for Ethernet or Ethernet + Dante
Optional accessories: 19" L-bearing rails, length 450 mm
Description

Good sound belongs everywhere - in the hotel lobby, in conference rooms, in schools and houses of worship. Demands are constantly increasing, not only in terms of quality, but also in terms of flexibility. Permanently installed and still flexible? This apparent contradiction can be resolved by the IPA Series DSP-based installation amplifiers.

The IPA 424 T is a professional, four-channel installation power amplifier with 4 x 240 watts. While the 70V/100V outputs are equipped with high quality toroidal core transformers, the low impedance 4-Ohm outputs are completely transformerless and guarantee the highest possible audio quality. The DSP functions include, amongst others, a parametric EQ with matching speaker library, dynamic tools, a matrix mixer, priority source selection and delay.

Despite this range of functions, the IPA Series power amps are easy to operate. Important functions such as signal, limit, protection and bridge mode are easily visible via the LEDs on the front panel.

HPF/LPF presets can be enabled directly on the device via DIP switches. The IPA 424 T is already prepared for remote control using future remote panels and paging microphones from LD Systems. The back-panel slot provides expansion card connectivity for additional future-proofing. The Ethernet card offers comprehensive configurability and management via software. The Ethernet+Dante card also offers Dante audio networking capabilities and connection to a wide range of Dante-enabled devices, in order to integrate the IPA 424 T into the Dante network and resolve more complex tasks.

Times are changing; rooms are redivided or rededicated, numbers of attendees increase or decrease based on unforeseen events, but with the IPA Series DSP-supported power amps, your installation is prepared for any situation. Scalability and future-proofing are the biggest advantages of the IPA Series. Its energy efficiency is also ideal thanks to the class-D technology and switchable auto standby.

The IPA 412 T variant with 4 x 120 watts is available for smaller installations.

Specifications
General
Product type Amplifier
Type Installation power amplifier
General data
Audio Channels 4
Output Circuitry Class D
Operating voltage Wide Range SMPS with PFC (power factor control)
Mains connector IEC socket
Auto-Standby Power Yes. Switchable (On-Off)
Time to Auto-standby 20 Min with no audio input signal
DSP Yes
Remote-Bus Yes
Indicators Front Panel: "PROT", "LIMIT", "SIG", "BRIDGE" and Mute Symbol LED´s. Power On/ Standby LED, Rear Panel: 4x Input Clip LED´s, Remote Lock LED (Red)
Controls Front panel On / off switch, standby
Controls Element Back Panel "BRG“ (Bridge), "PAR“ (Parallel), "ST“ (Stereo), Amplifier Channel Mode, Low-Z and High-Z switches (paired), Output Volume potentiometers, Preset A and B switches, Remote Lock, Remote ON/OFF, Remote-Mode, Standby On/Off
Inputs 4x Balanced Line Inputs, Remote Bus Audio Input
Input connectors 6-pin Terminal Block Pitch 3.81mm, Remote IN/OUT RJ45, Service connection Micro USB type B
Expansion Slot For optional Ethernet, or Ethernet + Dante cards
Cooling front to rear/side airflow, Passive + 2-zone temperature controlled active cooling
Operating voltage 100 V AC - 240 V AC, 50 - 60 Hz
Fuse T10AL 250 V
Inrush Current Power OFF-Standby 2.8 A
Inrush Current Standby-ON 0.5 A
Power Consumption @ Standby 0.9 W
Power Consumption @ idle mode 30 W
Power Consumption @ full load 1000 W
Operating temperature 0 °C - 40 °C; (max 60% relative humidity)
Width 483 mm
Height 44.5 mm
Depth 425 mm
Weight 11,36 kg
Amplifier Output Specifications, all outputs driven and loaded
Rated ouput power (1kHz @ 4 Ohms) 4 x 240 W (1.5 seconds sine burst)
Rated ouput power (1kHz @ 8 Ohms) 4 x 120 W (1,5 Seconds Sine Burst)
Rated ouput power (1kHz @ 16 Ohms) 4 x 60 W (1.5 Seconds Sine Burst)
Rated ouput power (1kHz @ 8 Ohms, bridged) 2 x 490W (1.5 Seconds Sine Burst)
Protection circuits Audio Limiter, DC, HF Protect, HPF (High-Z), short circuit, temperature, thermal overload
Minimum load impedance per channel 4 ohms Single-Ended, 8 ohms Bridge
Performance specifications
Nominal input sensitivity +5 dBu (Sine 1 kHz, Gain max)
THD + N < 0,03 % (Low-Z SPK OUT, +18 dBu, 20 Hz – 20 kHz)
Frequency response 18 Hz – 22 kHz (Low-Z OUT, -3 dB), 50 Hz – 23 kHz (High-Z OUT, -3 dB)
Digital Specifications
System Latency: 6.2 ms
AD/DA converter resolution 24 bit
AD/DA converter sampling rate 48 kHz
Optional accessories 19" L mounting rails ( AH - 876TL )
Downloads & links
Name
Category
Type
File size
LD Systems Catalogue Catalog pdf 38 MB
Product images Image files zip -
User´s Manual Manual pdf 6 MB
Tender documents Tender Specifications zip 162 KB
LD Systems Catalogue

Category: Catalog

Type: pdf

File size: 38 MB

Product images

Category: Image files

Type: zip

File size: -

User´s Manual

Category: Manual

Type: pdf

File size: 6 MB

Tender documents

Category: Tender Specifications

Type: zip

File size: 162 KB

(0) Download files
Stories
25. Oct 2022
LD Systems Multi-Room Sound System with ZONE X Matrix Processor in the Feldberghaus
12. Jul 2022
Pleasure with all of the senses – LD Systems provides sound for luxury Château Capitoul hotel in Southern France
28. Jan 2020
Press: Adam Hall Group Highlights New Audio and Lighting Products at ISE 2020
19. Mar 2019
Press: Adam Hall Group Premieres New Products and Visionary Campaigns at Prolight + Sound 2019
1. Feb 2021
Press: New Loudspeakers, DSP Amplifiers, Matrix Processors, and Much More – LD Systems Expands Its Portfolio for Permanent Installations
Related Products
Buy

For a quote on this item, please contact our sales department or make an appointment with our sales representatives.

Adam Hall North America Inc.
sales.us@adamhall.com
+1 973-335-7888