Contents and categories

Display all

Contents and categories

Series

Search suggestions

Display all results
  • NEW
  • NEW

AMP 205 2-Channel Mini Installation Power Amplifier 2x50 W @ 4 Ohm

Item No.: LDAMP205
Series: TICA
Professional mini amplifier
2 x 50W Class-D amplifier with low impedance outputs
Small form factor 1/3 19" rack, 1U
Silent operation with passive cooling
Connect to third party control for remote standby and volume control
External 100-240V power supply
Mounting plates for flexible inconspicuous installation, even above suspended ceilings
Auto standby to save power
Balanced line input and loudspeaker output on terminal strips
User-friendly front panel with signal, clip and protection LEDs
Optional rack tray for combining with other TICA® series products
 

Contents and categories

Display all

Contents and categories

Series

Search suggestions

Display all results
Professional mini amplifier
2 x 50W Class-D amplifier with low impedance outputs
Small form factor 1/3 19" rack, 1U
Silent operation with passive cooling
Connect to third party control for remote standby and volume control
External 100-240V power supply
Mounting plates for flexible inconspicuous installation, even above suspended ceilings
Auto standby to save power
Balanced line input and loudspeaker output on terminal strips
User-friendly front panel with signal, clip and protection LEDs
Optional rack tray for combining with other TICA® series products
Description

The LD AMP205 is a professional 2-channel mini installation amplifier. Part of the TICA® series, it combines of compact size, passive cooling, and high efficiency - ideal for a diverse range of audio installation applications.

Powered by a highly efficient 2x50W Class-D amplifier, it features 4 Ohm outputs and a user-friendly front panel, equipped with signal, clip, and protection LEDs. A gain switch helps the amplifier deal with a variety of input sources.

It's tiny 106 x 44 x 222 form factor and included mounting plates allow it to be installed discreetly almost anywhere; behind screens, under tables or even in in air-handling spaces and above plenum ceilings. Alternatively, it fits into ¼ 19 inch rack. Use the optional rack tray to slot up to four TICA® series products alongside each other and build a system to your exact requirements, using minimal rack space.

With remote control connectivity for third-party devices, you can adjust volume on either channel or put the power amplifier into standby mode at any time, even when it's hidden. Optional auto-standby saves power when no audio is running.

Terminal block connections for balanced line inputs and loudspeaker outputs make installation simple.

The perfect solution for professional installers and users looking for a compact, highly efficient and easy-to-integrate solution.

Specifications
General
Product type Installation power amplifier
Line inputs 2
Line input connectors 2 balanced line inputs, Pitch 3.81 mm terminal block (3-pin)
Line outputs 0
Powered outputs 2 with output mode selector (stereo / parallel / high power mode)
Cooling Convection
Priority levels 1
Input area
Nominal input sensitivity 14 dBu / 2 dBu (Gain +12dB switch)
Nominal input clipping 18 dBu (sine 1kHz, gain 0dB)
Input connector 2 x 3.81mm Terminal Block 3-pin
Standby wake up threshold 2.5 seconds
Type Class D
Output modes High power mode (ST / PAR / HPM), Parallel, stereo
Amplifier Outputs 2- channel (ST, PAR) / 1-channel (HPM)
Connector 4 - pin terminal block (pitch 5.08mm)
RMS Power ( W ) 1 x 100 W @ 2ohm (Continuous sine wave 1kHz 10sec, 4 ohm load), 2 x 50 W @ 4ohm (ST, PAR)
Power ( Peak ) (W) 1 x 110W @ 2ohm (Continuous sine wave 1kHz 10sec, 4 ohm load), 2 x 55 W @ 4ohm (ST, PAR)
Minimum load impedance 2 Ohms (HPM mode), 4 Ohm (stereo and parallel mode)
Frequency range 15 Hz - 20 kHz (-0,5 dB)
Protection circuits DC, over-current, short circuit, thermal overload, Undervoltage
Power supply
Type1 External SMPS
Operating voltage 100 V AC - 240 V AC, 50 - 60 Hz
Fuse 0
Secondary Voltage 24 V DC
Secondary Current 5 A
Secondary connector Terminal block 5.08 mm 2-pole
Primary Connector IEC
Safety class 1
Max. power consumption 105 W (sine 1kHz with 4 ohm load)
Idle power consumption 2 W (no signal input)
Standby power consuption < 1 W
Operating temperature ( non-condensing ) 0°C - 40°C; < 85% humidity
General data
Time to Auto-standby 20 Min.
Dimensions (W x H x D) ( height with rubber feet ) 142 mm x 53 mm x 221.7 mm
Accessories (included) External Power Supply, Mounting plates for surface mount applications, Terminal blocks for electrical connections.
Weight 1 kg
Downloads & links
Name
Category
Type
File size
User manual EN Manual pdf 649 KB
Tender documents Tender Specifications zip 162 KB
LD Systems Catalogue Catalog pdf 38 MB
Product images Image files zip -
User manual EN

Category: Manual

Type: pdf

File size: 649 KB

Tender documents

Category: Tender Specifications

Type: zip

File size: 162 KB

LD Systems Catalogue

Category: Catalog

Type: pdf

File size: 38 MB

Product images

Category: Image files

Type: zip

File size: -

(0) Download files
Buy

For a quote on this item, please contact our sales department or make an appointment with our sales representatives.

Adam Hall North America Inc.
sales.us@adamhall.com
+1 973-335-7888