Contents and categories

Display all

Contents and categories

Series

Search suggestions

Display all results
  • NEW
  • NEW

AMP 205 AV HDMI Audio De-Embedder & Amplifier 2x50W @ 4 Ohm

Item No.: LDAMP205AV
Series: TICA
Versions:
Professional mini amplifier with HDMI Audio de-embedder
HDMI In- and Out and stereo line outputs
2 x 50W Class-D amplifier with low impedance outputs
Compact form factor and passive cooling
Remote source select, standby and volume control
External 100-240V power supply
Mounting plates for flexible inconspicuous installation, even above suspended ceilings
Auto standby to save power
Balanced line output and loudspeaker output on terminal blocks
User-friendly front panel with signal, clip and protection LEDs.
Optional rack tray for combining with other TICA® series products
 

Contents and categories

Display all

Contents and categories

Series

Search suggestions

Display all results
Professional mini amplifier with HDMI Audio de-embedder
HDMI In- and Out and stereo line outputs
2 x 50W Class-D amplifier with low impedance outputs
Compact form factor and passive cooling
Remote source select, standby and volume control
External 100-240V power supply
Mounting plates for flexible inconspicuous installation, even above suspended ceilings
Auto standby to save power
Balanced line output and loudspeaker output on terminal blocks
User-friendly front panel with signal, clip and protection LEDs.
Optional rack tray for combining with other TICA® series products
Description

The LD Systems AMP 205 AV is the perfect complement to deliver sound from an AV system. Just connect your video source and it extracts the audio and delivers stereo audio to your loudspeakers. An HDMI pass though connection makes connection to your display device easy.

Powered by a highly efficient 2x50W Class-D amplifier, it features 4 Ohm outputs and a user-friendly front panel, equipped with signal, clip, and protection LEDs.

Its tiny form factor (142 x 44 x 222) and included mounting plates allow it to be installed discreetly almost anywhere; behind screens, under tables or even in air-handling spaces and above plenum ceilings. Alternatively, it fits into 1/3 19 inch rack. Use the optional rack tray to slot up to four TICA® series products alongside each other and build a system to your exact requirements, using minimal rack space.

The AMP 205 AV uses an external 24V power supply. Terminal block connections for the analogue outputs and GPIO connections make wiring easy.

Remote control connectivity for third-party devices lets you select between HDMI input and HDMI out (ARC). You can also adjust volume on either channel, and put the power amplifier into standby mode at any time, ideal for when the amp is hidden away. Optional auto-standby saves power when no audio is running.

The perfect solution for professional installers and users looking to deliver higher performance audio for the video systems.


Specifications
General
Product type
Installation power amplifier and HDMI Audio-Deembedder
Line inputs
0
Line outputs
2
Line output connectors
Balanced line outputs, Pitch 3.81 mm terminal block (3-pin)
Loudspeaker outputs
2 with output mode selector (Stereo / High Power Mode)
Cooling
Convection
HDMI specifications
Supported color format
RGB, YUV420, YUV422, YUV444
Max. data rate
48 Gbit/s
Resulution range
Up to 4K2K 60Hz
Color bit depth
8 bits per color
Chroma Sampling
4 : 4 : 4
HDMI standards
HDCP 1,4 - 2,3, HDMI 2,1
Number of HDMI Inputs
1
HDMI Input Connector
1 female HDMI type A
Number of HDMI Outputs
1
HDMI Output Connector
1 female HDMI type A
Standby wake up threshold
7 seconds
Thiele & Small Parameter
THD + N
> 0.006%
Frequency range
20Hz - 20kHz (-1dB)
Output level
+15 dBu (0dBFS / 1kHz)
3rd Party Control
Main Volume (VCA)
10k (Linear Taper) External Potentiometer, Pitch 3,5 mm terminal block (3-Pin)
Source select
External momentary button, Pitch 3.5mm terminal block (2-pin)
Power Standby
External momentary button, Pitch 3.5mm terminal block (2-pin)
Amplifier Output
Type
Class D
Output modes
Stereo, parallel, hHigh power mode (ST / PAR / HPM)
Amplifier Outputs
2- channel (STEREO) / 1-Channel (HPM)
Connector
4 - pin terminal block (pitch 5.08mm)
THD+N (-20dBFS)
> 0.005%
SRN ( A )
< 100dB
RMS Power ( W )
1 x 100 W @ 2ohm (Continuous sine wave 1kHz 10sec, 4 ohm load), 2 x 50 W @ 4ohm (ST, PAR)
Minimum load impedance
2 Ohms (HPM mode), 4 Ohm (stereo and parallel mode)
Frequency response
15 Hz - 20 kHz (-0,5 dB)
Protection circuits
DC protection, over-current, Short circuit, thermal overload
Type1
External SMPS
Operating voltage
100 V AC - 240 V AC, 50 - 60 Hz
Fuse
0
Power Supply Secondary
24 V DC
Secondary Current
3,5 A
Secondary connector
Terminal block 5.08 mm 2-pole
Primary Connector
IEC
Safety class
3
Max. power consumption
115W (sine 1kHz with 2x 4 ohm load)
Idle power consumption
6 W
Standby power consuption
< 1 W
Mains Inrush Current
1.5A @ 230V AC
Operating temperature ( non-condensing )
0°C - 40°C; < 85% humidity, non condensing
General data
Material
Plastic Front panel, Steel chassis
Dimensions (W x H x D) ( height with rubber feet )
142 mm x 53 mm x 221.7 mm
Weight
1,76 kg
Accessories (included)
External SMPS, Mounting plates for surface mount applications, Terminal blocks for electrical connections.
Downloads & links
Name
Category
Type
File size
User manual Manual pdf 2 MB
Tender documents Tender Specifications zip 162 KB
LD Systems Catalogue Catalog pdf 38 MB
Product images Image files zip -
User manual

Category: Manual

Type: pdf

File size: 2 MB

Tender documents

Category: Tender Specifications

Type: zip

File size: 162 KB

LD Systems Catalogue

Category: Catalog

Type: pdf

File size: 38 MB

Product images

Category: Image files

Type: zip

File size: -

(0) Download files
Stories
11. Jan 2024
Adam Hall Integrated Systems prepares for a busy ISE 2024
2. Nov 2023
LD Systems launches new TICA® Series for the installation market
Buy

For a quote on this item, please contact our sales department or make an appointment with our sales representatives.

Adam Hall North America Inc.
sales.us@adamhall.com
+1 973-335-7888