ZONE X 1208 D
Installations are becoming increasingly more complex. Where microphones and speakers once had to be switched or even rewired by hand, now there are flexible routing options using presets and automated processes. The DSP matrix processor ZONE X 1208 D from LD Systems enables all that and more.
With its DSP hybrid architecture, the ZONE X 1208 D can adapt your sound system for different circumstances and possible uses. Choose one of the different DSP templates and use the event scheduler to set up calendar-managed workflows with automated preset options. Everything you need: Twelve balanced mic/line inputs with low-noise microphone preamplifiers and separate switchable 48V phantom power as well as eight balanced line outputs are available. There are also eight GPI and GPO logic ports which can be used for automated processes and the integration of third-party devices.
The front panel with only 1 RU looks very tidy. The ZONE X 1208 D is convenient to set up and manage via Ethernet with the universal software Xilica Designer (Mac/Windows) providing an overview of all connections and settings. Dante 64 x 64 channels are available for audio over IP applications. The Dante standard opens up a whole world of compatible devices from different manufacturers for all conceivable applications. In addition, thanks to the additional REMOTE bus connection, the ZONE X 1208 D is already equipped for future remote panels and paging microphones from LD Systems.
From routing and processing of different microphone and speaker groups, in a church for example, to complex multi-room installations with calendar-managed routing for different configurations - the ZONE X 1208 D makes everything possible.
|Product type||Installation DSP Audio Matrix|
|Audio inputs||1 Remote Bus Audio input, 12 balanced Mic/line inputs|
|Audio output||8 balanced line outputs|
|Logic inputs||8 GPI - short to ground to activate|
|Logic outputs||Modes selectable per output|
|Connectors||3-pin Terminal Block Pitch 3.81mm, Ethernet RJ45, I/O Connectors, Remote IN RJ45, Service connection Micro USB type B|
|Indicators||Inputs 1 - 12 and outputs 1 - 8: signal indication white, Network, Power, Remote|
|Controls Front panel||no|
|Controls Element Back Panel||IP Reset, Power On/Off|
|Expansion Slot||Ethernet + Dante- (ZONEX1208D), For Ethernet- (ZONEX1208)|
|Operating voltage||Wide Range SMPS|
|Mains connector||3-pole IEC mains connection (mains socket)|
|Operating voltage||90 – 240 V AC; 50/60 Hz|
|Input fuse (mains)||T2,5 A L / 250 V|
|Inrush Current Power OFF-ON:||21 A|
|Power Consumption @ idle mode||23 W|
|Max. Power consumption||60 W W|
|Operating temperature||0°C - 40°C; < 60% humidity|
|Width||19“-Rack (483 mm)|
|Height||1 RU (44.5 mm)|
|Depth||315 mm (incl. terminal block connectors)|
|Nominal input sensitivity||-22 dBu (Sine 1 kHz, Gain max)|
|Nominal input clipping||+20 dBu (Sine 1kHz)|
|Distortion factor (THD+N)||+13 dBu Signal, <0,003% (Line IN – OUT), 20 Hz – 20 kHz, Gain 0 dB)|
|Intermodulation Distortion (SMPTE)||< 0.01% (-10dB below clip) Analyzer BW 90kHz|
|Frequency response||15 Hz – 22 kHz (+/-0.15 dB)|
|Input Impedance||Line 4k Ohms (balanced)|
|Signal-to-noise ratio||>117 dB @ +20 dBu, Gain 0 dB, 20 kHz BW, A-weighted|
|Dynamic range (DR AES17)||112 dB dB|
|Crosstalk||105 dB @ 10 kHz, 120 dB @ 1 kHz, 120 dB @ 100 Hz|
|CMRR IEC||> 60 dB (1 kHz)|
|Max. Gain||42 dB|
|DSP||40-bit floating point Analog Devices Dual-core SHARC+ processor|
|System Latency:||4.3 ms|
|AD/DA converter resolution||32 bit|
|AD/DA converter sampling rate||48 kHz|
For a quote on this item, please contact our sales department or make an appointment with our sales representatives.
Adam Hall North America Inc.